Benchmade Loco Knife Review

Benchmade started in 1979 and has since become one of the greatest knife companies around. Their knives are made of many things: steel, aluminum and titanium, to name a few. But perhaps the most important part of a Benchmade knife is expertise. They carefully measure every part at every step in the process. They use the best materials and equipment. They make world class knives for world class users and this is how. Every blade begins as a sheet of steel, so the first step in the process is laser cutting. At this step a laser cutting technician programs the laser to cut the steel into blanks, giving the blade its basic profile. If a part isn’t up-to-spec, it doesn’t become a Benchmade.

The second step is surface grinding. This is where the blank is ground to its precise width. A surface grind technician places each blank in its rack by hand and each side is ground to its specified thickness. Benchmade knives have no room for error, and neither does a blank’s thickness.

The third step in the process is the milling process. This is where blade holes, handles, and grooves are cut on high speed mills. One of the holes that is cut here is the blade pivot, which is crucial to the folding mechanism. The pivot tolerance is .0005 inches, because the slightest deviation there becomes exponential at the blade’s tip.

The fourth step in the process is beveling. This is the step that the blade starts to really take shape. Up to this point, the two sides of the blade are essentially flat. A Blade Beveling Technician bevels the knife blank one side at a time, and one of the most critical tasks here is to make sure the sides match perfectly. An imprecise bevel can hamper the blade’s balance, sharpness, strength, and mechanism function.

The fifth and sixth step are tied together: the back sanding and the finishing. Back sanding is where the back of the blade gets special attention. The sides of the blade have been beveled and milled, but the back has been relatively untouched since the original laser cutting. The back sanding technician sands the back of the blade until it is smooth. Finishing gives the blade a more refined look. The finishing technician stone washes the blades in a ceramic medium to remove any burrs and gives the blades a clean, polished appearance. When the blade is cleaned up, it is taken to laser marking to receive its one of a kind Benchmade mark.

The seventh and eight steps are the last steps and are also tied together. This time, it is the assembly and sharpening. Every Benchmade knife is assembled by hand, and it’s no surprise that there are more hand operations performed at this point in a knife’s production than at any other stage in the process. A sharpening technician puts a razor edge on the knife using a standing belt sander, and this step takes extraordinary concentration. Each blade is sharpened to a targeted 30-degree inclusive angle, 15 degrees on each side. The knife is sharp enough when it can cut through ultra-thin phonebook paper effortlessly without tearing. And only then is it truly a Benchmade.

Today, for Benchmade Month, we will be going over the Loco family of knives.

 

The Blade:

The blades on this family of knives is made out of CPM S30V steel. This is a premium formula of steel that is made by US based Crucible. This steel has excellent edge retention an resists rust effortlessly. It was designed in the US and is typically sued for the high-end premium pocket knives and expensive kitchen cutlery. The introduction of vanadium carbides brings extreme hardness into the steel alloy matrix. Dollar for dollar, this is generally regarded as one of the finest knife blade steels with the optimal balance of edge retention, hardness, and toughness. The only drawback to this steel is that it does prove to be pretty tricky to sharpen.

There are two different blade finishes that you get to choose from. The first is the satin finish, which is created by sanding the blade repeatedly in one direction. The key characteristic of this finish is that it shows the bevels of the blade while also showcasing the lines in the steel. This is a traditional finish that provides your knife with a very classic look. While it does work to reduce glares and reflections slightly, there are definitely more matte finishes.

The second finish option that you are presented with is a coated finish. This is a black coating that reduces the reflection and glare while also reducing wear and corrosion. Coating finishes can prolong the life of a blade by preventing corrosion or rust. Quality coatings add cost to a knife but provide more corrosion resistance, less reflection, and require less maintenance. However, ALL coatings can be scratched off after continuous heavy use, and the blade will then have to be re-coated.

The blade has been carved into a reverse tanto blade shape. This blade shape was designed by Bob Dozier and it actually resembles a reverse Drop Point style blade. This style of blade has no angular corners, but actually looks something like a Santoku. It does have a markedly different feel than other blade shapes. The point is much lower than the midpoint as with a spear point there are some differences as you would have better tip control than a spear point, but slightly less belly—like a halfway point between a spear point and a Wharncliffe blade. In general, there is no real rule with reverse tantos. Tanto blades have been made for excelling at piercing through tough materials. This was originally designed for armor piercing and was popularized by Cold Steel and is similar in style to Japanese long and short swords. While most tanto’s do not have a large belly, because it is a reverse tanto, there is a small belly that can work to slice a little bit. This family of knives has been designed as an everyday knife and also as a tactical knife. This knife shape makes for a good everyday knife option, because you do have the slight belly with the reversed tanto blade shape. But, it can also be a great tactical knife because the point is strong and sharp.

You have the option between two different edge styles. The first edge option is a plain edge. This is the more traditional edge option that you can go with and provides you with cleaner cuts than with a serrated edge. The plain edge is easier to get a finer edge and is easier to sharpen.

The plain edge excels at push cuts, slicing, skinning, and peeling.

The second option that you are presented with is a combo edge. This means that a portion of it is serrated and the other half is plain. The serrated portion is perfect for sawing through thicker and tougher materials. However, it will give you more jagged edges when you use it to cut. The benefits of a combo edge is that you have the serrated edges to get through the tougher things, but the plain edge for finer detail work.

 

The Handle:

The handle on the Loco family is made out of black G10. G10 is a grade of Garolite that is a laminate composite made of fiberglass. It has very similar properties to carbon fiber, yet it can be had for almost a fraction of the cost. The manufacturer takes layers of fiberglass cloth and soaks them in resin, then compresses them, and bakes them under pressure. The material that results is extremely tough, hard, very lightweight, and strong. In fact, G10 is considered the toughest of all the fiberglass resin laminates and stronger, although more brittle than Micarta. Checkering and other patterns add a texture to the handle, which makes for a solid, comfortable grip. The production process can utilize many layers of the same color, or varying different colors to achieve a unique cosmetic look on the g10 handle. Tactical folders and fixed blade knives benefit from the qualities of G10, because it is durable and lightweight, non-porous, and available in a variety of colors. While it is cheaper to produce than carbon fiber, it still has to be cut and machined into shape which is not as economical as the injection molding process used in FRN handles.

The handle has a deep finger groove to provide a secure grip, with a slight finger guard to keep your hand safe. After the finger groove, the handle curves until the butt of the handle, where it forms an angle to meet the spine of the handle. There is plenty of texture on the handle to give you a secure grip in most environments. The majority of the hardware on the handle is black, to match the G10. There is also a lanyard hole on the butt of the handle. This will come in handy when you are using the Loco as an everyday knife because it keeps it out of the way, but you have easy access to it. The lanyard will come in handy when you are using it as a tactical knife because with the lanyard, you can draw the knife out and into play quicker.

 

The Pocket Clip:

The pocket clip on the Loco family is a standard clip that can be attached to the knife tip up.

Benchmade Loco Knife
Benchmade Loco Knife

The Mechanism:

This knife is a manual opening knife that uses a thumb hole to assist you when you are opening your knife. Since the 1980s, the familiar round hole has most often been associated with folding knives from Spyderco. Over the years, numerous other knife makers have adopted or adapted the feature, one of which is Benchmade. There’s good reason for this industrial mimicry—the thumb hole works. Opening a folder equipped with a thumb hole or slot is just like using a thumb stud. By its very design, its ambidextrous. And many knife lovers favor a hole, because unlike a stud, it doesn’t protrude from the blade.

The Loco knives also feature the AXIS locking mechanism. The AXIS lock is a proprietary mechanism you’d only find on Benchmade knives, but due to its ingenuity and popularity among EDCers, its definitely worth knowing about. It’s easy to sue with one hand, but also important, its completely ambidextrous. The lock is made up of a spring tensioned bar that slides back and forth on a track cut into the handles of the knife. The butt of each blade featuring an AXIS lock has a flat spot that allows a spring tensioned bar to lock into place when the knife is opened. To close the knife, you pull the bar towards the back of the knife, using the thumb studs, and fold the blade shut. Right handers and lefties can both appreciate how easy it is to sue this lock, because the bar is accessible form both sides of the knife handle. Because this mechanism has plenty of moving parts involved, it can be difficult to disassemble for cleaning and maintenance.

 

The Specs:

The blade on the Loco knives are 3.68 inches long with a blade thickness of 0.160 inches. The overall length of the Loco knife is 8.62 inches long with a closed length of 4.94 inches. The handles on these knives are 0.67 inches thick. This knife weighs in at 6.56 ounces. This knife is made in the US.

 

Conclusion:

Benchmade named the 808 the Loco because it is crazy how overbuilt the knife is. A truly robust tactical knife with the refined style of custom hardware. This knife has a unique styling. This Black Class model utilizes the Benchmade AXIS mechanism and uses an oval shaped cutout in the blade to open it. Even without thumb studs or a flipper function, this large blade opens extremely smooth and closes just the same. The beefy black G10 handle scales, with stainless steel liners, are contoured providing a comfortable ergonomic grip—even for prolonged periods of time. The Loco takes the unique factor to the next level by featuring a reverse tanto style blade that gives exceptional performance thanks to the S30V stainless steel as well as custom hardware fond on both the AXIS lock and pivot pin and even the back spacers.

Facebooktwitterpinterest
Facebooktwitteryoutubeinstagram